Skip to main content
Skip table of contents

Safety Instructions

Read these instructions carefully and save them for future reference.

  • All cautions and warnings on the equipment should be noted.

  • Lay this equipment on a stable surface during set up. A drop or fall could cause damage.

  • The warranty will be invalidated if the device is damaged during installation or replacement of system expansions.

  • Use the original power adapter and power cord only.

  • Make sure the power adapter and power cord are laid so that people do not step on them. Do not place anything over the power adapter or power cord.

  • Disconnect this equipment from the main supply before cleaning. Do not use liquid or spray detergent to clean. Clean only with a wipe or cloth.

  • Before opening the device, first, switch it off and then disconnect the power plug. Observe the specification in the user manual.

  • If the equipment is not used for a long time, disconnect the equipment from the main electric supply to avoid damage by transient overvoltage.

  • Make sure that no liquids leak into the device (danger of electric shock, fire, short circuit).

  • Do not insert foreign objects into the device (danger of electric shock, fire, short circuit).

  • If one of the following situations occurs, have the equipment checked by service personnel:

    • The power adapter, power cord or plug is damaged.

    • The equipment has been exposed to moisture.

    • The equipment does not work well, or you cannot get it working according to the user manual.

    • The equipment has been dropped or damaged.

    • The equipment has obvious signs of breakage.

  • Do not leave this equipment in an unconditioned environment. Storage temperature below -20 °C (-4 °F) or above 60 °C (140 °F) may cause damage to the equipment.

  • Do not use this equipment in an unconditioned environment. Unless otherwise stated in the technical specifications, operational conditions may not exceed the following limits, it may damage the equipment:

    • Vertical usage:
      Temperature: 0 °C to 35 °C, 32 °F to 95 °F
      Humidity: 20 % to 80 %, non-condensing

    • Horizontal usage (only with optional rubber feet, no VESA mount):
      Temperature: 0 °C to 35 °C, 32 °F to 95 °F
      Humidity: 20 % to 80 %, non-condensing

  • To avoid overheating in the horizontal position, use the optional rubber feet and tilt the device to the left so that the power button is on the left-hand side.

  • Note that even in closed rooms local temperatures may increase, for instance in case the device is exposed to strong sun radiation. Protect the device from external heat sources.

  • Ensure that air is free to circulate through the product. Do not use in a poorly ventilated place. Do not cover it with a cloth or place it on soft ground. Objects surrounding the device may block the airflow. Keep a minimum distance of 20 cm around the device for sufficient ventilation.

Lithium Battery Caution

  • The lithium battery (button cell) installed in the device may only be replaced by authorized, specially trained personnel.

  • Contact your supplier or the manufacturer for servicing and repairs.

  • Danger of explosion if the battery is incorrectly replaced. The lithium battery may only be replaced with a battery identical or equivalent to the one recommended by the manufacturer.

  • Dispose of used batteries according to the manufacturer’s instructions.

Excessive Sound Pressure

Excessive sound pressure from ear-/headphones can cause hearing damage/hearing loss. Adjustment of the volume control as well as the equalizer to other settings than the center position may increase the ear-/headphones output voltage and therefore the sound pressure level. The use of factors influencing the ear-/headphones output other than those specified by the manufacturer (e.g. operating system, equalizer software, firmware, driver) may increase the ear-/headphones output voltage and therefore the sound pressure level.

UL 62368

This equipment must be grounded. The power cord for the equipment must only be connected to socket-outlets providing earthing connection.

For the latest product information, visit www.igel.com.

JavaScript errors detected

Please note, these errors can depend on your browser setup.

If this problem persists, please contact our support.